Reports from the community highlight a few quirks you should know before installing: The "Bundle" Trap : If you purchased the V30 as part of the CK888 keyboard combo
Finally figured out the MOTOSPEED V30 software – here’s what you need to know ⚡ motospeed v30 software
: You can configure up to six DPI levels, ranging from 500 to 3500 DPI (the native limit of the PMW3320 sensor). The software allows you to toggle specific levels on or off and assign unique LED colors to each level so you can identify your setting at a glance. Reports from the community highlight a few quirks
The software allows you to customize the colors and patterns for the 14 integrated LEDs To fix this, open Device Manager , locate
: Some users report that Windows incorrectly identifies the mouse as a keyboard. To fix this, open Device Manager , locate the devices under "Keyboards" labeled as "HID keyboard," and uninstall them. This often forces the system to correctly recognize the device as a mouse.
[ 35HD-NAS-E ] MRT GigaNAS 35HD-NAS-E 3.5" SATA Single Bay NAS (gemini) ================== !!! IMPORTANT NOTICE !!! ================== This firmware image is compatible with factory bootloader only ============================================================== Product specification: Vendor: MRT Communication Ltd. CPU/SoC: Cortina Systems/Storlink devices CS3516/SL3516 (FA526) @ 300MHz (ARM) Memory: 64 MiB (DDR1 SDRAM) Flash size: 16 MiB (Parallel NOR): 3 MiB for kernel and 6+6 MiB for rootfs (1 MiB misc: boot, VCTL, FIS, config) Bootloader: Storlink Boot Loader (zImage) Ethernet ports: 1 x 1000 Mbps (PHY: Marvell 88E1111) Wireless: None MiniPCI slots: None USB ports: 1 x USB 2.0 (back side) Input voltage: 12V DC / 2A via Philmore 258 Barrel Plug, Type: Adaptaplug N (Polarity: Center positive wiring) RTC battery: CR2032 / 3V lithium battery UART settings: 19200 baud, 8-N-1 mode (TTL compatible logic levels) UART pinout: JP4 / Vcc (3.3V): 1, RX: 2, TX: 3, GND: 5. Device alias: Multicase HD-35SN ============================================================== NOTICE: This image works with the official package repository. ============================================================== Files: - openwrt-15.05.1-gemini-mrt-giganas-35hd-nas-e-zImage.img LZMA kernel (parition: Kern), - openwrt-15.05.1-gemini-mrt-giganas-35hd-nas-e-bootlog.txt device bootlog (dmesg), - openwrt-15.05.1-gemini-mrt-giganas-35hd-nas-e-squashfs.img squashfs filesystem (parition: Ramdisk), - openwrt-15.05.1-gemini-mrt-giganas-35hd-nas-e-sysupgrade.tar.gz sysupgrade image, - openwrt-15.05.1-gemini-mrt-giganas-35hd-nas-e-packages.txt packages list (opkg list-installed), - openwrt-15.05.1-gemini-mrt-giganas-35hd-nas-e.md5 MD5 checksum. ========= CHANGELOG ========= Chaos Calmer 15.05.1 (r48532) - openwrt-15.05.1-gemini-mrt-giganas-35hd-nas-e* - 2018-03-14 ------------------------------------------------------------------------------------------- [UPD] Updated to Openwrt Chaos Calmer v15.05.1 (r48532), [NEW] Darkmatter theme for LuCI added. Chaos Calmer 15.05 (r46767) - openwrt-gemini-mrt-35hd-patafix+jp3-led* - 2016-07-30 ----------------------------------------------------------------------------------- [FIX] Memory size modified to 64MB, [MOD] The device has no Machine ID so it uses ID of Raidsonic NAS4210-B: 0x1fff (8191), [NEW] JP3 (GPIO #14) unsoldered LED pin support added (mrt35hd:jp3:hdd -> idedisk), [FIX] Default trigger changed for JP3 pin: idedisk (kernel based), [FIX] ATA Channel #1 disabled, [NEW] Kernel modules compiled into the kernel: leds-gpio, ledtrig-ide-disk. [FIX] Sysugrade and ramdisk image published and firmware size fixed (hddapp removed), [NEW] Necessary kernel modules and packages added to rootfs image. [ FIRMWARE SUMMARY ] Kernel version: 3.18.23 Image format: zImage (LZMA) Rootfs Type: SquashFS Build server: itsuki.dev.dtech.hu Build host: Debian GNU/Linux, Version 7.0 Latest build: 2018-03-14 Status: PRODUCTION TEST RESULT: OK